AIX/PReP under QEMU How-To

AIX/PReP under QEMU How-To

Fetch the 40p-20190406-aix-boots branch and  compile qemu-system-ppc:

configure --target-list=ppc-softmmu

download the OFW image q40pofw-serial.rom configured  for the serial line.

create an empty hard disk image:

qemu-img create -f qcow2 aix-hdd.qcow2 8G

Concerning the VGA graphics: OFW can utilize the S3-Trio emulation done by Hervé, but AIX 5.1 can’t use it yet. For now, the serial line rules, but if you feel adventurous you can try using it omitting  the -vga none -nongraphic part.

qemu-system-ppc -M 40p -bios q40pofw-serial.rom -serial telnet::4441,server -hda aix-hdd.qcow2 -cdrom
/path/to/aix-5.1-cd1.iso  -vga none -nographic

Then in another terminal window:

telnet localhost 4441

The following text will appear:

QEMU PReP/40p, Serial #0, 128 MiB memory installed
Open Firmware, built  April 06, 2019 17:47:55
Copyright (c) 1995-2000, FirmWorks.
Copyright (c) 2014,2017,2019 Artyom Tarasenko.

Type any key to interrupt automatic startup
Boot device: /pci/ethernet  Arguments: 
The DHCP server did not specify a boot server

Boot load failed

ok

Once you see the “ok” prompt, type

ok boot cdrom:2

 

Then be patient, it takes some minutes till the first greeting appears and then some more before the installer starts.

Then answerer the installer questions. On my machine the copy process takes nearly one hour. At 93% it stalls after installing “mtools” for something like 10 Minutes, and then for another 10 minutes after “FAILURES” section, but don’t panic, eventually it will continue.

Once the install is done the emulated machine reboots to the “ok” prompt again. Type

ok boot disk

Supported AIX versions

I tested it with AIX 5.1 only. In theory it might work with 4.3.3 – 5.1 (a smoke test shows that at least the installer does start with AIX 4.3.3), let me know if you tested it. The 6015 support was officially discontinued in AIX 5.2, and probably the corresponding drivers were removed. I haven’t looked it up, as I don’t have a 5.2 media.

Networking in AIX 4.3.3 - 5.1 under QEMU

It looks like the PCNet driver (aka kent) is broken in AIX. I think the "busio" value used to look different in the previous versions. The networking can still be set up though. After performing the install, login as root and do the following (^D and ^C are Control-D and Control-C respectively):

# cat > lance-chg.asc
CuAt:
        name = "ent0"
        attribute = "busio"
        value = "0x01000000"
        type = "O"
        generic = "D"
        rep = "nr"
        nls_index = 3
^D
# odmchange -o CuAt -q "name=ent0 and attribute=busio" lance-chg.asc
# rmdev -l ent0
# mkdev -l ent0
# ifconfig en0 10.0.2.15
# ping 10.0.2.2
PING 10.0.2.2: (10.0.2.2): 56 data bytes
64 bytes from 10.0.2.2: icmp_seq=0 ttl=255 time=4 ms
64 bytes from 10.0.2.2: icmp_seq=1 ttl=255 time=3 ms
^C
#

If you try it with adifferent AIX version, before changing the busio, check first whether you have to modify it:

odmget -q "name=ent0 and attribute=busio" CuAt

In case  you get

value = "0x01000000"

you don't have to change it.

Your feedback is welcome!

Last updated on 2020.02.07